1 files changed, 83 insertions, 0 deletions

diff --git a/pintos-progos/devices/pit.c b/pintos-progos/devices/pit.c
new file mode 100644
index 0000000..bfb1889
--- /dev/null
+++ b/pintos-progos/devices/pit.c
@@ -0,0 +1,83 @@
+#include "devices/pit.h"
+#include <debug.h>
+#include <stdint.h>
+#include "threads/interrupt.h"
+#include "threads/io.h"
+
+/* Interface to 8254 Programmable Interrupt Timer (PIT).
+   Refer to [8254] for details. */
+
+/* 8254 registers. */
+#define PIT_PORT_CONTROL          0x43                /* Control port. */
+#define PIT_PORT_COUNTER(CHANNEL) (0x40 + (CHANNEL))  /* Counter port. */
+
+/* PIT cycles per second. */
+#define PIT_HZ 1193180
+
+/* Configure the given CHANNEL in the PIT.  In a PC, the PIT's
+   three output channels are hooked up like this:
+
+     - Channel 0 is connected to interrupt line 0, so that it can
+       be used as a periodic timer interrupt, as implemented in
+       Pintos in devices/timer.c.
+
+     - Channel 1 is used for dynamic RAM refresh (in older PCs).
+       No good can come of messing with this.
+
+     - Channel 2 is connected to the PC speaker, so that it can
+       be used to play a tone, as implemented in Pintos in
+       devices/speaker.c.
+
+   MODE specifies the form of output:
+
+     - Mode 2 is a periodic pulse: the channel's output is 1 for
+       most of the period, but drops to 0 briefly toward the end
+       of the period.  This is useful for hooking up to an
+       interrupt controller to generate a periodic interrupt.
+
+     - Mode 3 is a square wave: for the first half of the period
+       it is 1, for the second half it is 0.  This is useful for
+       generating a tone on a speaker.
+
+     - Other modes are less useful.
+
+   FREQUENCY is the number of periods per second, in Hz. */
+void
+pit_configure_channel (int channel, int mode, int frequency)
+{
+  uint16_t count;
+  enum intr_level old_level;
+
+  ASSERT (channel == 0 || channel == 2);
+  ASSERT (mode == 2 || mode == 3);
+
+  /* Convert FREQUENCY to a PIT counter value.  The PIT has a
+     clock that runs at PIT_HZ cycles per second.  We must
+     translate FREQUENCY into a number of these cycles. */
+  if (frequency < 19)
+    {
+      /* Frequency is too low: the quotient would overflow the
+         16-bit counter.  Force it to 0, which the PIT treats as
+         65536, the highest possible count.  This yields a 18.2
+         Hz timer, approximately. */
+      count = 0;
+    }
+  else if (frequency > PIT_HZ)
+    {
+      /* Frequency is too high: the quotient would underflow to
+         0, which the PIT would interpret as 65536.  A count of 1
+         is illegal in mode 2, so we force it to 2, which yields
+         a 596.590 kHz timer, approximately.  (This timer rate is
+         probably too fast to be useful anyhow.) */
+      count = 2;
+    }
+  else
+    count = (PIT_HZ + frequency / 2) / frequency;
+
+  /* Configure the PIT mode and load its counters. */
+  old_level = intr_disable ();
+  outb (PIT_PORT_CONTROL, (channel << 6) | 0x30 | (mode << 1));
+  outb (PIT_PORT_COUNTER (channel), count);
+  outb (PIT_PORT_COUNTER (channel), count >> 8);
+  intr_set_level (old_level);
+}